Transtar 2K urethane non-sanding White Sealer (Gallon w/ Activator) Tra-6221

Description

TRANSTAR 6221 KWIK SEAL 2K URETHANE SEALER WHITE (GALLON)
Transtar Kwik Seal 2K Urethane Sealer has been specifically formulated as a premium quality sealer to be used over a
variety of substrates. Kwik Seal offers excellent adhesion to bare metal, aluminum, SMC, fiberglass, old paint finishes
and all Transtar primers. Kwik Seal has excellent leveling and gloss hold out properties and is compatible with most
basecoat/clearcoat and single stage systems. It is one of the most innovative products on the market today! Utilizing
Transtar’s “Star Shade” system, these colors can be intermixed at established ratios to create a wide variety of color
offerings for optimum basecoat coverage.
MIX RATIO:
4 parts Sealer, 1 part Activator, 1 part Reducer
POT LIFE:
2.5 hours @ 70°F and 50% relative humidity
DRY TO SAND TIMES:
45 minutes to 1 hour
SANDING:
Sealer should be topcoated within 3 hours to avoid any adhesion problems.
After 3 hours, scuff sand with a gray scuff pad or sand (wet or dry) with 600 grit paper.
APPLICATION & MIXING:
Mix 4 parts Sealer with 1 part activator and 1 part of Urethane Grade Reducer (TDS600 & TDS601) Series suitable
for shop conditions. Mix and strain before using.
Wet-on-wet:
Apply one full even wet coat to achieve 1.0 mils. Sealer should be topcoated within three hours to avoid adhesion problems. After three hours, scuff sand the sealer with a gray scuff pad or sand (wet or dry) with 600 grit sand paper, before applying sealer or basecoat color.
As a barrier coat:
Kwik Seal can be used as a barrier coat to seal over troublesome substrates (ie old finishes). The barrier coat helps prevent lifting of existing finish by the basecoat upon base coat application. Apply 2-3 medium coats, allowing each coat to flash 5-10 minutes before applying the next coat. Allow to dry thoroughly and scuff or sand before applying topcoat. Note: For best results in temperatures above 85°F (29°C) or in high air flow spray booths, a narrow spray gun pattern will help prevent dry spray. Clean spray gun immediately after use.
DRY TIME SCHEDULE:
# of                                                           Tape/Denib                   Min Recoat                        Max Recoat
Coats          Temperature                           Time                              Time                                    Time
1                  65-75°F (18-24°C)            30-45 Min                       20 Min                                  5 Hrs
2                  65-75°F (18-24°C)            60-90 Min                       30-45 Min                            6 Hrs
3                  65-75°F (18-24°C)            90-120 Min                     45-60 Min                            7 Hrs
1                  75-85°F (24-29°C)             20-30 Min                       15-20 Min                            4 Hrs
2                  75-85°F (24-29°C)             30-60 Min                        20-30 Min                           5 Hrs
3                  75-85°F (24-29°C)             60-90 Min                        30-45 Min                           6 Hrs
1                  90°F+ (29°C+)                    10-20 Min                       10-15 Min                            3 Hrs
2                  90°F+ (29°C+)                    15-30 Min                       15-20 Min                            4 Hrs
3                  90°F+ (29°C+)                    30-45 Min                       20-30 Min                            5 Hrs
NOTE: Topcoating without sufficient dry times may result in die-back.If the max recoat time is exceeded, you must sand the sealer with either 500-600 wet or 320-400 dry. Denib with
1200-1500 wet. Going Coarser could gouge the sealer.
YOU WILL RECEIVE 1 GALLON OF TRANSTAR KWIK SEALER WHITE 6221 AND 1 QUART OF TRANSTAR SEALER ACTIVATOR 6254
ALSO AVAILABLE IN GREY AND BLACK 2K SEALER
SHIPPING TO ALASKA & HAWAII EXTRA
NO P.O. BOXES
PROVISION Auto Body Supply
Providing Quality to Professionals. Buy with confidence.