Thinkscan Plus OBD2 Scanner Check ABS SRS ECM BCM Diagnostic Tool Code Reader

Description

Store category
Sign Up Now !
You may also like
Thinkscan Plus OBD2 Scanner Code Reader ABS SAS SRS ECM BCM System Diagnostic
Product Description
Thinkscan Plus
series products are a new generation of mid-to-high end DIY products based on Android system by THINKCAR, which can realize online upgrade of diagnostic software. Its main functions include not only OBD/EOBD standard protocol diagnosis, but more importantly, it has professional vehicle diagnosis software and maintenance software, which can perform comprehensive diagnosis on all vehicle electronic control systems. Different series support different systems and functions.
1. For Engine：
The diagnostic tool can help detect the engine ignition, fuel injection, air and fuel ratio, and exhaust emission conditions in Engine system to enhance vehicle performance, save energy and reduce exhaust emission.
2. For Transmission:
It makes great sense in the safe driving when your car is slipping or difficult to shift. This diagnostic scanner can figure the problems out via reading codes in the Transmission system, or check the health status via live data viewing.
3. For ABS:
Diagnosing an ABS problem should always start with a visual inspection of all brake components, next you will need to retrieve ABS codes to tell you where the problem is, and this is what this scanner does for you.
4. For SRS:
SRS, safety restraint system, is made up of impact sensors, a control module, and the airbags themselves, and this diagnostic device can detect every electronic parameter to check its health status.
5. For Body Control Module:
Control function, to control many electrical appliances. Check
mainly control the electrical appliances used in the car body, such as lamps, wipers, door locks, power windows, sunroofs, etc.
Support 28+Maintenance Reset
(3 Reset is Free
)
1.Oil Reset:
The lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset themileage or driving time to zero after the maintenance, so the maintenance light will go out and the systemwill start a new maintenance cycle.
2.DPF Regeneration:
DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuouscombustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reducePM ignition combustion) to stabilize the filter performance.
3.AFS(headlamp) Reset:
This feature is used to initialize the adaptive headlamp system.According to the ambient light intensity, theadaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjustthe headlamp lighting angle while monitoring the vehicle speed and body posture.
4.EGR Adaption:
This function is used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced.
5.Brake-pad Reset:
lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to theon-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad.Otherwise, the car alarms.
6.Immobilize:
To prevent the car being used by unauthorized keys, the anti-theft key matching function must beperformed so that the immobilizer control system on the car identifies and authorizes remote control keysto normally use the car. When the ignition switch key, ignition switch, combined instrument panel,ECu,BCM, or remote control battery is replaced, anti-theft key matching must be performed
7.Windows Calibration:
This feature is designed to perform door window matching to recover ECU initial memory, and recover theautomatic ascending and descending function of power window.
8.Coolant Bleeding:
Use this function to activate the electronic water pump before venting the cooling system.
9.Steering Angle Reset:
To reset the steering angle, first find the relative zero point position for the car to drive in straight line.Taking this position as reference, the ECU can calculate the accurate angle for left and right steering.After replacing the steering angle position sensor, replacing steering mechanical parts (such as steeringgearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recoveringcar body, you must reset the steering angle.
10.Injector Coding:
Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder soas to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced,injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identifyinjectors to accurately control fuel injection.
11. Seat Calibration:
This function is applied to match the seats with memory function that are replaced and repaired.
12.Transport Mode:
ln order to reduce power consumption, the following functions may be disabled,including limiting thevehicle speed, not waking up the door opening network, and disabling the remote control key, etc. At thistime, the transport mode needs to be deactivated to restore the vehicle to normal.
13.Battery Matching:
This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, inwhich the original low battery fault information will be cleared and battery matching will be done.
14.Airbag Reset:
This function resets the airbag data to clear the airbag collision fault indicator. When the vehicle collidesand the airbag deploys, the corresponding fault code of the collision data appears, the airbag indicatorlights up, and the fault code cannot be cleared. Since the data inside the airbag computer is disposable,it is required that all new accessories must be replaced, but after performing this function, the data of theairbag computer can be recovered and the fault code can be cleared, the airbag light will go out, and theairbag computer can continue to use.
15.Tyre Reset:
This function is used to set the size parameters of the modified or replaced tire.
16.ODO Reset:
a) ODo reset is to copy,write, or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable, so that the odometer shows the actual mileage.
b)Usually when the mileage is not correct due to the damaged vehicle speed sensor or odometer failure, it is necessary to do ODo reset after maintenance.
17.ABS Bleeding:
When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system torestore ABS brake sensitivity. lf the ABS computer,ABS pump, brake master cylinder, brake cylinder, brakeline, or brake fluid is replaced, the ABS bleeding function must be performed to bleed the ABS.
18.Gear Learning:
The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computerto more accurately diagnose engine misfires. lf gear learning is not performed for a car equipped withDelphi engine, the MlL turns on after the engine is started.The diagnostic device detects the DTC P1336'gear not learned'. In this case, you must use the diagnostic device to perform gear learning for the car.After gear learning is successful, the MIL turns off. After the engine ECU, crankshaft position sensor, orcrankshaft flywheel is replaced, or the DTC 'gear not learned" is present, gear learning must be performed.
19.Language Change:
This function is used to change the system language of the vehicle central control panel.
20.Adblue Reset:(Diesel Engine Exhaust Gas Filter)
After the diesel exhaust treatment fluid (car urea) is replaced or flled up, urea reset operation is required.
21.Elec. Throtle Adaption:
Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learningvalue of the ECU returns to the initial state.By doing these, the movement of the throttle (or idle motor)can be more accurately controlled, thus adjust the intake volume.
22.Suspension Matching:
This function can adjust the height of the body. When replacing the body height sensor in the airsuspension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration.
23.AIF Reset:
This function is applied to set or learn Air/Fuel ratio parameters.
24.Nox Sensor Reset:
NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. lf theNOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalyticconverter learned value stored in the engine ECu.
25.TPMS Reset:
After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting functionmust be performed to reset tire pressure and turn off the tire pressure MIL.Tire pressure resetting mustbe performed after maintenance is performed in the following cases: tire pressure is too low, tire leaks, tirepressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged,andtire is replaced for the car with tire pressure monitoring function.
26.AT Learning:
This function can complete the gearbox self-learning to improve gear shifting quality. When the gearbox isdisassembled or repaired (after some of the car battery is powered off), it will lead to shift delay or impactproblem. In this case, this function needs to be done so that the gearbox can automatically compensateaccording to the driving conditions so as to achieve more comfortable and better shift quality.
27.Sunroof Initialization:
This function can set the sunroof lock off, closed when it rains,sliding / tilting sunroof memory function,temperature threshold outside the car etc.
28.Stop/Start Reset:
This function is used to open or close the automatic start-stop function via setting the hidden function inECU(provided that the vehicle has a hidden function and supported by hardware).
OBDII functions:
- Request Current Powertrain Diagnostic Data
- Request Powertrain Freeze Frame Data
- Request Emission-Related Diagnostic Trouble Codes
- Clear/Reset Emission-Related Diagnostic Information
- Request Oxygen Sensor Monitoring Test Results
- Request On-Board Monitoring Test Results for Specific Monitored Systems
- Request Emission-Related Diagnostic Trouble Codes Detected During Current or Last Completed Driving Cycle
- Request Control of On-Board System Test or Component
- Request Vehicle Information
- Request Emission-Related Diagnostic Trouble Codes with Permanent Status
Thinkscan plus
Support Diagnposis with English,German,Spanish,French, Italian, Japanese, Portuguese,Russian.
Live Data Stream Graph & Record Data & Diagnosis Record Playback & Print Report
The professional vehicle scanner tool can scientific graph data, record data, play back data, freeze frame,and print reports.
In the real-time diagnosis process, important diagnosis information can be instantly stored in the memory, including reading of fault codes and frozen frames and real-time data streams.
After real-time diagnosis is completed, Diagnosis function record playback, the diagnosis information and process previously saved in the memory can be replayed to facilitate the analysis of various data information.
One-click generation of a diagnosis report after diagnosis will help users quickly solve problems, avoid blind maintenance, and save money/time.
Support List:
America (1996-2020 model) :
for Chrysler, for Ford, for GM
Asia(2003 to 2020 model):
for Acura, for AU Ford (For Australian Market Only), for Daewoo, for Honda, for Holden (For Australian Market Only), for Hyundai, for Infiniti, for Isuzu, for Kia, for Lexus, for Mahindra , for Mazda, for Mitsubishi, for Nissan, for Perodua (For Malaysian Market Only), for Proton (For Malaysian Market Only), for Scion, for Subaru, for Suzuki, for TATA , for Toyota, for Daihatsu, for Hyundai_CV, for Ssangyong, for Proton
European (2001-2020 model):
for Abarth, for Alfa-Romeo, for Audi, for AstonMartin, for BMW, for Bugatti, for Bentley, for Citroen, for Dacia, for EU Ford, for Fiat, for Jaguar, for Lancia, for Land Rover,for Maserati, for Maybach, for Mercedes Benz,for Mini, for Opel, for Peugeot, for Porsche, for Renault, for Saab, for Seat, for Skoda, for Smart, for Sprinter, for Vauxhall, for Volvo, for VW, for VW_CV, for Ferrari, for Lamborghini, for Maybach, for Rolls-Royce
Payment
Delivery details
Terms of sales
About us
Contact us
Payment
1.We accept payment by PayPal only !
2.Payment should be completed Within 8 days after buyer places the order, or else an ebay Unpaid Case will be opened .
3.If you Can Not Pay in time or Don't Want to Buy this product any more , please Cancel the transaction Before the Unpaid Case is Opened.
Delivery details
1.All of the items will be shipped to buyer's EBAY address,please confirm your address on Ebay before you buy.
2.Your order will be usually shipped out the same or next business days once the payment is made and cleared, except on weekends and holidays.
3.Most of products are checked and tested carefully before shipment.Well Packed protects your items with suitable material so as to avoid damage during transit.
4. If your package delayed few days, due to any unexpected factor, please wait patiently. your kind understanding would be highly appreciated!
Terms of sales
1. We can not guarantee that you will be able to access every module or use every piece of cd/dvd software. Compatibility varies due to variations in the cars modlue or availabilty of year it released from original factory
2.It's the buyer's responsibility to complete clearance when parcel reached your Customs.
3.We are not responsible for buyers's local taxes, please consult local Customs for Tax Details.
About us
We are eager to be your professional parner of automobile diagnostic tool.
We support remote assistance by Teamviewer if you have any difficulty in software installation.
Contact us
1. We are committed to providing customers with the best products and services
，
Please do not hesitate to leave us your positive feedback if you are satisfaction with our products ,delivery or services .
2. If you have Any Questions, Please do not hesitate to Contact Us by email/ ebay message. We will reply you within 12 hours and do our best solve the problem with you
（
Except on Weekends and Holidays
）
.
3.Work time:GMT8 (9:00am-18:30 PM) ,Except for Saturday (9:00-11:00AM) .
Feedback